chanegd to epics 7

epics/iocs/ISTTOKrpi/configure/CONFIG_SITE

@@ -23,8 +23,7 @@ CHECK_RELEASE = YES
 
 # To install files into a location other than $(TOP) define
 #   INSTALL_LOCATION here.
-INSTALL_LOCATION=/opt/epics/iocs/ISTTOKrpi
-#</absolute/path/to/install/top>
+#INSTALL_LOCATION=</absolute/path/to/install/top>
 
 # Set this when the IOC and build host use different paths
 #   to the install location. This may be needed to boot from

epics/iocs/ISTTOKrpi/configure/RELEASE

@@ -1,13 +1,12 @@
 # RELEASE - Location of external support modules
 #
-# IF YOU MAKE ANY CHANGES to this file you must subsequently
-# do a "gnumake rebuild" in this application's top level
-# directory.
+# IF YOU CHANGE ANY PATHS in this file or make API changes to
+# any modules it refers to, you should do a "make rebuild" in
+# this application's top level directory.
 #
-# The build process does not check dependencies against files
-# that are outside this application, thus you should do a
-# "gnumake rebuild" in the top level directory after EPICS_BASE
-# or any other external module pointed to below is rebuilt.
+# The EPICS build process does not check dependencies against
+# any files from outside the application, so it is safest to
+# rebuild it completely if any modules it depends on change.
 #
 # Host- or target-specific settings can be given in files named
 #  RELEASE.$(EPICS_HOST_ARCH).Common
@@ -15,7 +14,7 @@
 #  RELEASE.$(EPICS_HOST_ARCH).$(T_A)
 #
 # This file is parsed by both GNUmake and an EPICS Perl script,
-# so it can ONLY contain definititions of paths to other support
+# so it may ONLY contain definititions of paths to other support
 # modules, variable definitions that are used in module paths,
 # and include statements that pull in other RELEASE files.
 # Variables may be used before their values have been set.
@@ -23,25 +22,21 @@
 # the CONFIG_SITE file.
 
 # Variables and paths to dependent modules:
-SUPPORT=$(EPICS_BASE)/../synApps_5_8/support
+#MODULES = /path/to/modules
+#MYMODULE = $(MODULES)/my-module
 
 # If using the sequencer, point SNCSEQ at its top directory:
-SNCSEQ = $(SUPPORT)/seq-2-2-1
-ASYN     = $(SUPPORT)/asyn-4-26
-STREAM = $(SUPPORT)/stream-2-6a
-AUTOSAVE = $(SUPPORT)/autosave-5-6-1
-DRVASYNI2C = $(EPICS_BASE)/../modules/drvAsynI2C
+#SNCSEQ = $(MODULES)/seq-ver
 
-#
 # EPICS_BASE should appear last so earlier modules can override stuff:
-EPICS_BASE = /usr/local/epics/base
+EPICS_BASE = /home/pi/Apps/epics7/epics-base
 
 # Set RULES here if you want to use build rules from somewhere
 # other than EPICS_BASE:
 #RULES = $(MODULES)/build-rules
 
-# These allow developers to override the RELEASE variable settings
-# without having to modify the configure/RELEASE file itself.
+# These lines allow developers to override these RELEASE settings
+# without having to modify this file directly.
 -include $(TOP)/../RELEASE.local
+-include $(TOP)/../RELEASE.$(EPICS_HOST_ARCH).local
 -include $(TOP)/configure/RELEASE.local
-

epics/iocs/ISTTOKrpi/iocBoot/iocISTTOKrpi/save/iocISTTOKrpi.sav

@@ -1,4 +1,4 @@
-# autosave R5.3	Automatically generated - DO NOT MODIFY - 210510-201940
+# autosave R5.3	Automatically generated - DO NOT MODIFY - 210511-111857
 ! 2 channel(s) not connected - or not all gets were successful
 ISTTOK:central:PULSE-NUMBER.VAL 0
 ISTTOK:central:LogMessage.VAL 

epics/iocs/ISTTOKrpi/iocBoot/iocISTTOKrpi/st.cmd

@@ -4,9 +4,9 @@
 ## everywhere it appears in this file
 
 < envPaths
-epicsEnvSet( "STREAM_PROTOCOL_PATH", "$(TOP)/protocols" )
+epicsEnvSet( "STREAM_PROTOCOL_PATH", "$(TOP)/db" )
 epicsEnvSet( "SAVE_DIR", "$(TOP)/iocBoot/$(IOC)" )
-epicsEnvSet( "EPICS_CA_ADDR_LIST", "localhost 192.168.1.152")
+epicsEnvSet( "EPICS_CA_ADDR_LIST", "localhost 192.168.1.120 192.168.1.152")
 
 cd "${TOP}"
 
@@ -25,17 +25,18 @@ dbLoadRecords("db/ISTTOKtda8444.db","P=ISTTOK:,R=central:")
 dbLoadRecords("db/ISTTOKmachineControl.db","P=ISTTOK:,R=central:")
 
 ## Load Serial drivers
-drvAsynSerialPortConfigure("RS0","/dev/ttyUSB0")
+#drvAsynSerialPortConfigure("RS0","/dev/ttyUSB0")
 #drvAsynSerialPortConfigure("RS0","/dev/ttyAMA0")
 
-asynSetOption("RS0", 0, "baud", "9600")
-asynSetOption("RS0", 0, "bits", "8")
-asynSetOption("RS0", 0, "parity", "none")
-asynSetOption("RS0", 0, "stop", "1")
-asynSetOption("RS0", 0, "clocal", "Y")
-asynSetOption("RS0", 0, "crtscts", "N")
+#asynSetOption("RS0", 0, "baud", "9600")
+#asynSetOption("RS0", 0, "bits", "8")
+#asynSetOption("RS0", 0, "parity", "none")
+#asynSetOption("RS0", 0, "stop", "1")
+#asynSetOption("RS0", 0, "clocal", "Y")
+#asynSetOption("RS0", 0, "crtscts", "N")
 
-dbLoadRecords("db/ISTTOKpfeiffer.db","P=ISTTOK:,R=central:,bus=RS0")
+# Pfeiffer sensor are connectoed to other RPI /(192.168.1.120)
+#dbLoadRecords("db/ISTTOKpfeiffer.db","P=ISTTOK:,R=central:,bus=RS0")
 
 # connect to the MAIL server mail.ipfn.tecnico.ulisboa.pt
 #		,priority,noAutoConnect,noProcessEos

epics/iocs/RELEASE.local

@@ -5,12 +5,16 @@ SUPPORT=$(HOME)/Apps/epics7/support
 #
 ASYN=$(SUPPORT)/asyn
 STREAM=$(SUPPORT)/StreamDevice
+#CALC=$(SUPPORT)/calc
+AUTOSAVE = $(SUPPORT)/autosave
+DRVASYNI2C =$(SUPPORT)/drvAsynI2C
+SNCSEQ=$(SUPPORT)/seq-2-2
+
 #  IPAC release V2-7 or later is required.
-IPAC=
+#IPAC=
 #$(SUPPORT)/ipac-2-15
 #
 #  # SEQ is required for testIPServer
-SNCSEQ=
 #$(SUPPORT)/seq-2-2-5
 #
 CALC=